# Working with contours

**URL:** <https://forums.sketchup.com/t/working-with-contours/57326>\
**Category:** Pro\
**Created:** [December 10, 2017, 1:49pm UTC](https://forums.sketchup.com/t/working-with-contours/57326 "2017-12-10T13:49:23Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![bzakaras](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/bzakaras/32/41433_2.png) [@bzakaras](https://forums.sketchup.com/u/bzakaras)\
**Post date:** [December 10, 2017, 1:49pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/1 "2017-12-10T13:49:23Z")

</div>

Hi All,  
Can someone direct me to a good tutorial series for the following?:  
Let’s say I’m modeling a simple one story house with a walkout below with the house placed into a hillside.  
I started the sandbox tools pretty thoroughly and I’m familiar with the TIN and Hidden geometry aspects, not to mention sketch up nuances  
with respect to how it doesn’t work i.e. flip edges etc.  
I know how to import geoterrainn and slice it into topo layers/lines ( if that makes sense as a working methodology)  
I understand the stamp tool smoove tool and how to land or hover something onto existing terrain.  
I think I would be able to import surveyors I don’t care either to do you were 3-D and work from that if I needed to.  
My problem is that I am pretty old-school i.e. accustomed to sitting down with trace over topo lines with a building footprint and sketching and reconnecting topo lines or deadending them into objects as necessary or retaining walls or whatever.  
I just don’t see a sketch up a Quillivant to this process.  
All the sketchup tools and methodology that I see don’t have a parallel to this process maybe I just need to change my thinking but so far after watching probably 10 tutorials I cant seem to find someone who gets to the point of a here’s how are you meld a new building into an existing landscape and have it looking and making sense.  
Thanks to anyone Who can point me in the right direction.

---

<div class="post-metadata">

**Author:** ![DaveR](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/daver/32/7601_2.png) [@DaveR](https://forums.sketchup.com/u/DaveR)\
**Post date:** [December 10, 2017, 1:55pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/2 "2017-12-10T13:55:36Z")

</div>

If I understand correctly, you just want to put a hole in your terrain to fit your building?

---

<div class="post-metadata">

**Author:** ![Wo3Dan](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/wo3dan/32/7450_2.png) [@Wo3Dan](https://forums.sketchup.com/u/Wo3Dan)\
**Post date:** [December 10, 2017, 1:56pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/3 "2017-12-10T13:56:58Z")

</div>

> [@bzakaras](#):
>
> … here’s how are you meld a new building into an existing landscape …

Doesn’t ‘Intersect Faces With …’ do the job for you?

---

<div class="post-metadata">

**Author:** ![Box](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/box/32/235164_2.png) [@Box](https://forums.sketchup.com/u/Box)\
**Post date:** [December 10, 2017, 1:58pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/4 "2017-12-10T13:58:12Z")

</div>

Or Stamp.

---

<div class="post-metadata">

**Author:** ![bzakaras](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/bzakaras/32/41433_2.png) [@bzakaras](https://forums.sketchup.com/u/bzakaras)\
**Post date:** [December 10, 2017, 2:37pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/5 "2017-12-10T14:37:18Z")

</div>

Yes that’s part of it but no not really I want to understand how to manipulate contours with ease in a micro versus macro sort of way and not just the add detail sandbox command.

---

<div class="post-metadata">

**Author:** ![bzakaras](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/bzakaras/32/41433_2.png) [@bzakaras](https://forums.sketchup.com/u/bzakaras)\
**Post date:** [December 10, 2017, 2:38pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/6 "2017-12-10T14:38:56Z")

</div>

I suppose that might work ( or be a tool in the toolbox l) that’s how I created contour lines out of Geoterrain

---

<div class="post-metadata">

**Author:** ![bzakaras](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/bzakaras/32/41433_2.png) [@bzakaras](https://forums.sketchup.com/u/bzakaras)\
**Post date:** [December 10, 2017, 3:28pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/7 "2017-12-10T15:28:38Z")

</div>

OK To better illustrate my point see attached picture of an AutoCAD drawing which typifies a site plan for me.  
This was done using an AutoCAD (2D I think) survey imported as the background.  
My question is can I use sketch up to insert my model into a site plan like this and be able to manipulate and study the contours and eventually smooth them out to look like real terrain? Ie what is the workflow?  
I typically work in 1 foot or 6 inch topo increments do I create this giant layer Cake of contours and use the push pull tool to move them around and create new contours with curvy lines as contour edges? how you do it and then have it remain Easily editable?

 ![image](https://global.discourse-cdn.com/sketchup/original/3X/2/2/22be5bcedd7cf627bf455d5e868add807857e647.jpeg)

---

<div class="post-metadata">

**Author:** ![Cotty](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/cotty/32/251290_2.png) [@Cotty](https://forums.sketchup.com/u/Cotty)\
**Post date:** [December 10, 2017, 4:37pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/8 "2017-12-10T16:37:06Z")

</div>

I would use Toposhaper with the traced contour lines.

---

<div class="post-metadata">

**Author:** ![Wo3Dan](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/wo3dan/32/7450_2.png) [@Wo3Dan](https://forums.sketchup.com/u/Wo3Dan)\
**Post date:** [December 10, 2017, 5:01pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/9 "2017-12-10T17:01:25Z")

</div>

> [@bzakaras](#):
>
> … how you do it and then have it remain Easily editable?

they are editable like how you would move edges, faces or vertices. Or at best you may scale one or two curved contour lines or move them up or down. But that’s probably not what you are after. You don’t want to manipulate the terrain, do you?

If you do have the contours as welded segments → to curves in SketchUp, you can apply ‘From Contours’ from the ‘Sandbox’ tool set on a selection of contour lines. That would get you the skinned terrain surface. You’ll need to clean up the result by removing unwanted edges though.

---

<div class="post-metadata">

**Author:** ![bzakaras](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/bzakaras/32/41433_2.png) [@bzakaras](https://forums.sketchup.com/u/bzakaras)\
**Post date:** [December 10, 2017, 7:02pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/10 "2017-12-10T19:02:14Z")

</div>

Thanks, I’ll check it out.

```
-----------------------------------------From: "Carsten Unverzagt" 

```

To:  
Cc:

Cotty [1] SketchUp Sage  
December 10

```
I would use Toposhaper with the traced contour lines.

```

---

<div class="post-metadata">

**Author:** ![bzakaras](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/bzakaras/32/41433_2.png) [@bzakaras](https://forums.sketchup.com/u/bzakaras)\
**Post date:** [December 10, 2017, 7:09pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/11 "2017-12-10T19:09:46Z")

</div>

Good tips. I am also familiar with some extension plug in that  
“welds” line segments into one continuous line.

```
Yes indeed I DO want to manipulate the terrain, that's the whole

```

point, not just landing (stamp) a building on it.

```
You say moveable/editable just like regular geometry. Ok I buy that

```

but using the push/pull tool to alter grades seems overly basic. Just  
as you can offset lines but you can’t grab sections of line section  
and move the vertice and end up with a smooth (topo) line can you? and  
what do you do with the vertical face between topo elevations? I’ve  
seen vids where you have to arduously have to go thru and delete all  
the “bottom” lines and then use sanbox tools to reconnect the parallel  
topo top lines. Again seems amateurish.

```
-----------------------------------------From: "G H Hubers" 

```

To:  
Cc:

Wo3Dan [1] SketchUp Sage  
December 10

```
bzakaras: 

… how you do it and then have it remain Easily editable?  

they are editable like how you would move edges, faces or vertices.

```

Or at best you may scale one or two curved contour lines or move them  
up or down. But that’s probably not what you are after. You don’t  
want to manipulate the terrain, do you?

```
If you do have the contours as welded segments -> to curves in

```

SketchUp, you can apply ‘From Contours’ from the ‘Sandbox’  
tool set on a selection of contour lines. That would get you the  
skinned terrain surface. You’ll need to clean up the result by  
removing unwanted edges though.

---

<div class="post-metadata">

**Author:** ![bzakaras](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/bzakaras/32/41433_2.png) [@bzakaras](https://forums.sketchup.com/u/bzakaras)\
**Post date:** [December 10, 2017, 7:52pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/12 "2017-12-10T19:52:56Z")

</div>

Ok, I’ve looked at that a bit and it seems to have potential. (would  
be nice to find a vid with SPOKEN WORDS!), but…

```
I didn't see in the demos the kind of (archaic, old school) technique

```

I would like to use. That being draw and manipulate all the contour  
lines in 2D plan (with them actually being 2D, ie all at the same  
elevation) or via using Sketchup Standard Top view from above in which  
the topo lines could be at varying elevations say from a Geolocate  
Terrain import.

```
Drop building footprint in for reference, manipulate contour lines in

```

plan only and then jump to 3D. Can Toposhaper do that?

```
And then to edit, jump back to 2D and presuming the topo is in a

```

group and building (and other hard surface lines as well) are in  
another separate group so the geometry doesn’t stick to each other,  
and/or topo is on its own layer and it all works to revise and relook  
at?

```
Thanks,

Z

-----------------------------------------From: "Carsten Unverzagt" 

```

To:  
Cc:

Cotty [1] SketchUp Sage  
December 10

```
I would use Toposhaper with the traced contour lines.

```

---

<div class="post-metadata">

**Author:** ![RTCool](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/rtcool/32/181048_2.png) [@RTCool](https://forums.sketchup.com/u/RTCool)\
**Post date:** [December 10, 2017, 9:28pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/13 "2017-12-10T21:28:49Z")

</div>

> [@bzakaras](#):
>
> via using Sketchup Standard Top view from above in which
> 
> the topo lines could be at varying elevations

I was thinking along those lines: create a working plane, elevate it to match the elevation of any contour, and then just draw the new, changed contour line. The surface could have transparency so you can see everything below, but you’d have to keep changing the height of the plane for each contour line. It would allow your brain to think in terms of contour lines which is how I learned it all.

My limited experience has always been, asking the surveyor for a dwg file and importing the contours, which SU easily converts to terrain. I never erase or edit the existing condition, only move what’s changed to another layer I can turn off to hide. As with existing building renovations, we always want to document what’s Existing, Removed, and New.

---

<div class="post-metadata">

**Author:** ![Charevir](https://avatars.discourse-cdn.com/v4/letter/c/e99b99/32.png) [@Charevir](https://forums.sketchup.com/u/Charevir)\
**Post date:** [December 10, 2017, 9:34pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/14 "2017-12-10T21:34:54Z")

</div>

You ask for tutorial then Look Winning for SketchUp (1,2) and Daniel Tal (8) You Tube videos on my playlist  
https://www.youtube.com/embed/videoseries?list=PLbCjnmQpREo4LDam-vV7n2KA0c071wp2H&wmode=transparent&rel=0&autohide=1&showinfo=1&enablejsapi=1  
This link is related to Daniel Teal video: [Learning to model terrain in SketchUp](http://www.sketchup-ur-space.com/2012/sept/learning-to-model-terrain-in-SketchUp-1.html)

Also Nick Sonder in his book SkechUp & Layou for Architecture describe the workflow you named old school methodology in one of his project, but I think it is covered by all the above links.

---

<div class="post-metadata">

**Author:** ![bzakaras](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/bzakaras/32/41433_2.png) [@bzakaras](https://forums.sketchup.com/u/bzakaras)\
**Post date:** [December 10, 2017, 10:31pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/15 "2017-12-10T22:31:21Z")

</div>

Good tips, thanks a lot!

---

<div class="post-metadata">

**Author:** ![bzakaras](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/bzakaras/32/41433_2.png) [@bzakaras](https://forums.sketchup.com/u/bzakaras)\
**Post date:** [December 11, 2017, 5:09pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/16 "2017-12-11T17:09:22Z")

</div>

Thanks all. “Terrain Modeling in SketchUp” by Daniel Tal Land F/X answers my initial questions most precisely. Will check the other vids as well.

Hello, plug in/extensions!

---

<div class="post-metadata">

**Author:** ![Charevir](https://avatars.discourse-cdn.com/v4/letter/c/e99b99/32.png) [@Charevir](https://forums.sketchup.com/u/Charevir)\
**Post date:** [December 11, 2017, 9:14pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/17 "2017-12-11T21:14:09Z")

</div>

i’m glad that it works for you. I’ve updated my playlist, it’s worth if you can check it.

---

<div class="post-metadata">

**Author:** ![bzakaras](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/bzakaras/32/41433_2.png) [@bzakaras](https://forums.sketchup.com/u/bzakaras)\
**Post date:** [December 11, 2017, 9:42pm UTC](https://forums.sketchup.com/t/working-with-contours/57326/18 "2017-12-11T21:42:30Z")

</div>

Will do.

---

<div class="post-metadata">

**Author:** ![horace](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/horace/32/30173_2.png) [@horace](https://forums.sketchup.com/u/horace)\
**Post date:** [December 17, 2017, 12:02am UTC](https://forums.sketchup.com/t/working-with-contours/57326/19 "2017-12-17T00:02:56Z")

</div>

John Brock of Brock Works Inc did a very good series of tutorials on placing a walk out basement in a SU contour model. here is the first one.

[![](https://global.discourse-cdn.com/sketchup/original/3X/8/3/83407b63587f8f867476a813c52d11bf2723f243.jpeg "Site Modeling in SketchUp: Part I: Existing and Excavated Site") ](https://www.youtube.com/watch?v=Ec_2QVkwgYI)

---

<div class="post-metadata">

**Author:** ![bzakaras](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/bzakaras/32/41433_2.png) [@bzakaras](https://forums.sketchup.com/u/bzakaras)\
**Post date:** [December 17, 2017, 3:04am UTC](https://forums.sketchup.com/t/working-with-contours/57326/20 "2017-12-17T03:04:10Z")

</div>

Thanks I’ll check it out.

[Next page](https://forums.sketchup.com/t/working-with-contours/57326.md?page=2)
