# Need help with the push/pull

**URL:** <https://forums.sketchup.com/t/need-help-with-the-push-pull/51918>\
**Category:** SketchUp\
**Created:** [September 20, 2017, 11:53am UTC](https://forums.sketchup.com/t/need-help-with-the-push-pull/51918 "2017-09-20T11:53:56Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![DaveMc](https://avatars.discourse-cdn.com/v4/letter/d/ecae2f/32.png) [@DaveMc](https://forums.sketchup.com/u/DaveMc)\
**Post date:** [September 20, 2017, 11:53am UTC](https://forums.sketchup.com/t/need-help-with-the-push-pull/51918/1 "2017-09-20T11:53:56Z")

</div>

I push/pulled 1 arc on one face and I am tryin to do it on the next side and I can only push it till it makes contact with the first arc and will not go push all the way through. I have attached the file.  
Thank you for any [Leg.skp](https://forums.sketchup.com/uploads/short-url/1dD5EGj18nvNFak9i6aPEm3ND6s.skp) (20.3 KB)  
help.

---

<div class="post-metadata">

**Author:** ![DaveR](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/daver/32/7601_2.png) [@DaveR](https://forums.sketchup.com/u/DaveR)\
**Post date:** [September 20, 2017, 11:56am UTC](https://forums.sketchup.com/t/need-help-with-the-push-pull/51918/2 "2017-09-20T11:56:30Z")

</div>

Without looking at your file, I’m going to guess you should be using Follow Me instead of Push/Pull to sweep the profile around the leg.

Edit: Now that I’ve had a chance to look at it, my guess was correct. Draw the leg blank, put the arc on the right side face. Select the top front and left edges of the leg, get Follow Me and click on the waste side of the arc.

---

<div class="post-metadata">

**Author:** ![Wo3Dan](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/wo3dan/32/7450_2.png) [@Wo3Dan](https://forums.sketchup.com/u/Wo3Dan)\
**Post date:** [September 20, 2017, 12:03pm UTC](https://forums.sketchup.com/t/need-help-with-the-push-pull/51918/3 "2017-09-20T12:03:15Z")

</div>

Or in case of your uploaded file:  
When applying Push/Pull to push beyond existing interfering geometry, hit [Ctrl] once to leave a copy of the face behind. That way you can push/pull all the way through.  
Once you have done so, select all \> right click on selection \> intersect faces with selection  
Then start erasing unwanted geometry to get your wanted result.  
You may need to reverse some back faces in the end.

 ![image](https://global.discourse-cdn.com/sketchup/original/3X/e/5/e539089fb12a056952ea1dbb5442b9d796feb571.png)  
Green marked face has been pushed beyond.  
Red face still has to be done.  
Intersect afterwards.  
Clean up.

---

<div class="post-metadata">

**Author:** ![ecati](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/ecati/32/28643_2.png) [@ecati](https://forums.sketchup.com/u/ecati)\
**Post date:** [September 20, 2017, 1:36pm UTC](https://forums.sketchup.com/t/need-help-with-the-push-pull/51918/4 "2017-09-20T13:36:47Z")

</div>

You can do it this way.

 ![5](https://global.discourse-cdn.com/sketchup/original/3X/9/a/9ad264a1ded56db558e0c4abceb7da7c028b56ff.gif)

---

<div class="post-metadata">

**Author:** ![DaveR](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/daver/32/7601_2.png) [@DaveR](https://forums.sketchup.com/u/DaveR)\
**Post date:** [September 20, 2017, 1:38pm UTC](https://forums.sketchup.com/t/need-help-with-the-push-pull/51918/5 "2017-09-20T13:38:48Z")

</div>

It’s a heckuva lot faster to just use Follow Me. No screwing around with Intersect Faces or deleting unneeded geometry.

---

<div class="post-metadata">

**Author:** ![system](https://global.discourse-cdn.com/sketchup/original/3X/f/2/f2a121500b085ed60806607a82720b092d800bb3.png) [@system](https://forums.sketchup.com/u/system)\
**Post date:** [December 21, 2017, 5:38am UTC](https://forums.sketchup.com/t/need-help-with-the-push-pull/51918/6 "2017-12-21T05:38:49Z")

</div>

Closed on December 21, 2017, 5:38am UTC

This topic was automatically closed 91 days after the last reply. New replies are no longer allowed.
