# Holes in surfaces

**URL:** <https://forums.sketchup.com/t/holes-in-surfaces/21671>\
**Category:** SketchUp\
**Created:** [March 8, 2016, 12:04pm UTC](https://forums.sketchup.com/t/holes-in-surfaces/21671 "2016-03-08T12:04:44Z")\
**Posts on this page:** 7\
**Page:** 1

<div class="post-metadata">

**Author:** ![olafur](https://avatars.discourse-cdn.com/v4/letter/o/ecae2f/32.png) [@olafur](https://forums.sketchup.com/u/olafur)\
**Post date:** [March 8, 2016, 12:04pm UTC](https://forums.sketchup.com/t/holes-in-surfaces/21671/1 "2016-03-08T12:04:44Z")

</div>

After a bit of editing I am left with two problems I seem to be unable to fix. In the pink area of the picture there are holes that I can not fill. There are no lines surrounding them and simply drawing a rectangle over them does not work.  
Similarily, in the lower half of the gray part, the bottom half is simply invisibla. I can not cover this area.  
Is this a known problem?  
Thanks,  
Ólafur

 ![](https://global.discourse-cdn.com/sketchup/original/2X/4/49787ff6cdf0553a66886309884485563ed8bb6b.JPG)

---

<div class="post-metadata">

**Author:** ![DaveR](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/daver/32/7601_2.png) [@DaveR](https://forums.sketchup.com/u/DaveR)\
**Post date:** [March 8, 2016, 12:11pm UTC](https://forums.sketchup.com/t/holes-in-surfaces/21671/2 "2016-03-08T12:11:39Z")

</div>

Very likely it is a known problem. Typically the problem is that the user has created edges which are not coplanar. If you draw a diagonal between corners, do you get faces? Your image doesn’t give much useful information for diagnosing the problem. Could you share the SKP file? With that to look at, I expect you’d get the answer you need almost immediately.

---

<div class="post-metadata">

**Author:** ![olafur](https://avatars.discourse-cdn.com/v4/letter/o/ecae2f/32.png) [@olafur](https://forums.sketchup.com/u/olafur)\
**Post date:** [March 8, 2016, 2:14pm UTC](https://forums.sketchup.com/t/holes-in-surfaces/21671/3 "2016-03-08T14:14:21Z")

</div>

DaveR, as is typical I now managed to remove the problem. What I did was to highlight til gray part by double-clicking. Then I deselected the grey area, top and left and right lines. Then I Moved the bottom line down until it matched the adjacent walls. On the other half I noticed there were some ghost lines that apparently were in some way inherited from the “Pallur” layer. These I managed to isolate and delete. However when I pressede Delete the lines did not disappear. Instead, they remained blue until I attempted to select them again. Then they disappeared.  
There is still a problem of the same nature. Next to the lower left of the door opening there is still a remnant of this behaviour. This I have not fixed yet.  
It is possibly of interest that I have had similar problems many times with this model.  
I include the skp file should you recognize the problem and be able to steer me in the right direction.  
Thanks.

---

<div class="post-metadata">

**Author:** ![Box](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/box/32/235164_2.png) [@Box](https://forums.sketchup.com/u/Box)\
**Post date:** [March 8, 2016, 2:20pm UTC](https://forums.sketchup.com/t/holes-in-surfaces/21671/4 "2016-03-08T14:20:28Z")

</div>

Your included skp is not included.

---

<div class="post-metadata">

**Author:** ![olafur](https://avatars.discourse-cdn.com/v4/letter/o/ecae2f/32.png) [@olafur](https://forums.sketchup.com/u/olafur)\
**Post date:** [March 8, 2016, 4:34pm UTC](https://forums.sketchup.com/t/holes-in-surfaces/21671/5 "2016-03-08T16:34:54Z")

</div>

Strange. I dragged the skp onto my reply, just like I did with the jpg in my original message. Is there a size limit? My skp is 31mb

---

<div class="post-metadata">

**Author:** ![Box](https://sea2.discourse-cdn.com/sketchup/user_avatar/forums.sketchup.com/box/32/235164_2.png) [@Box](https://forums.sketchup.com/u/Box)\
**Post date:** [March 8, 2016, 4:37pm UTC](https://forums.sketchup.com/t/holes-in-surfaces/21671/6 "2016-03-08T16:37:22Z")

</div>

Yep, it’s 28 mb too big.  
3D warehouse will accept up to 50mb and you can post the link here.  
However, I suggest you go to Window/Model info/Statistics and hit the Purge button, then save and try to attach again.

---

<div class="post-metadata">

**Author:** ![olafur](https://avatars.discourse-cdn.com/v4/letter/o/ecae2f/32.png) [@olafur](https://forums.sketchup.com/u/olafur)\
**Post date:** [March 10, 2016, 8:52am UTC](https://forums.sketchup.com/t/holes-in-surfaces/21671/7 "2016-03-10T08:52:53Z")

</div>

I suppose the Public folder in Dropbox will do the same [https://dl.dropboxusercontent.com/u/2802435/G38%20breytingar%202015%20mjórra%20eldhús%20í%20horni.skp](https://dl.dropboxusercontent.com/u/2802435/G38%20breytingar%202015%20mj%C3%B3rra%20eldh%C3%BAs%20%C3%AD%20horni.skp)  
best regards,  
Ólafur
